.

ESP32_Temperture-Node/.pio/libdeps/esp32doit-devkit-v1/Adafruit BME280 Library/examples/bme280test/bme280test.ino

@@ -0,0 +1,90 @@
+/***************************************************************************
+  This is a library for the BME280 humidity, temperature & pressure sensor
+
+  Designed specifically to work with the Adafruit BME280 Breakout
+  ----> http://www.adafruit.com/products/2652
+
+  These sensors use I2C or SPI to communicate, 2 or 4 pins are required
+  to interface. The device's I2C address is either 0x76 or 0x77.
+
+  Adafruit invests time and resources providing this open source code,
+  please support Adafruit andopen-source hardware by purchasing products
+  from Adafruit!
+
+  Written by Limor Fried & Kevin Townsend for Adafruit Industries.
+  BSD license, all text above must be included in any redistribution
+  See the LICENSE file for details.
+ ***************************************************************************/
+
+#include <Wire.h>
+#include <SPI.h>
+#include <Adafruit_Sensor.h>
+#include <Adafruit_BME280.h>
+
+#define BME_SCK 13
+#define BME_MISO 12
+#define BME_MOSI 11
+#define BME_CS 10
+
+#define SEALEVELPRESSURE_HPA (1013.25)
+
+Adafruit_BME280 bme; // I2C
+//Adafruit_BME280 bme(BME_CS); // hardware SPI
+//Adafruit_BME280 bme(BME_CS, BME_MOSI, BME_MISO, BME_SCK); // software SPI
+
+unsigned long delayTime;
+
+void setup() {
+    Serial.begin(9600);
+    while(!Serial);    // time to get serial running
+    Serial.println(F("BME280 test"));
+
+    unsigned status;
+    
+    // default settings
+    status = bme.begin();  
+    // You can also pass in a Wire library object like &Wire2
+    // status = bme.begin(0x76, &Wire2)
+    if (!status) {
+        Serial.println("Could not find a valid BME280 sensor, check wiring, address, sensor ID!");
+        Serial.print("SensorID was: 0x"); Serial.println(bme.sensorID(),16);
+        Serial.print("        ID of 0xFF probably means a bad address, a BMP 180 or BMP 085\n");
+        Serial.print("   ID of 0x56-0x58 represents a BMP 280,\n");
+        Serial.print("        ID of 0x60 represents a BME 280.\n");
+        Serial.print("        ID of 0x61 represents a BME 680.\n");
+        while (1) delay(10);
+    }
+    
+    Serial.println("-- Default Test --");
+    delayTime = 1000;
+
+    Serial.println();
+}
+
+
+void loop() { 
+    printValues();
+    delay(delayTime);
+}
+
+
+void printValues() {
+    Serial.print("Temperature = ");
+    Serial.print(bme.readTemperature());
+    Serial.println(" °C");
+
+    Serial.print("Pressure = ");
+
+    Serial.print(bme.readPressure() / 100.0F);
+    Serial.println(" hPa");
+
+    Serial.print("Approx. Altitude = ");
+    Serial.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
+    Serial.println(" m");
+
+    Serial.print("Humidity = ");
+    Serial.print(bme.readHumidity());
+    Serial.println(" %");
+
+    Serial.println();
+}