light sleep: add software workaround for esp32s3 gpio reset issue

components/esp32c3/Kconfig

@@ -192,23 +192,4 @@ menu "ESP32C3-Specific"
             If enabled, this disables the linking of binary libraries in the application build. Note
             that after enabling this Wi-Fi/Bluetooth will not work.
 
-    config ESP32C3_LIGHTSLEEP_GPIO_RESET_WORKAROUND
-        bool "light sleep GPIO reset workaround"
-        default y
-        select PM_SLP_DISABLE_GPIO if FREERTOS_USE_TICKLESS_IDLE
-        help
-            ESP32C3 will reset at wake-up if GPIO is received a small electrostatic pulse during
-            light sleep, with specific condition
-
-            - GPIO needs to be configured as input-mode only
-            - The pin receives a small electrostatic pulse, and reset occurs when the pulse
-              voltage is higher than 6 V
-
-            For GPIO set to input mode only, it is not a good practice to leave it open/floating,
-            The hardware design needs to controlled it with determined supply or ground voltage
-            is necessary.
-
-            This option provides a software workaround for this issue. Configure to isolate all
-            GPIO pins in sleep state.
-
 endmenu  # ESP32C3-Specific

components/esp_hw_support/Kconfig

@@ -34,6 +34,25 @@ menu "Hardware Settings"
             bool
             default y if IDF_TARGET_ESP32 || IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
 
+        config ESP_SLEEP_GPIO_RESET_WORKAROUND
+            bool "light sleep GPIO reset workaround"
+            default y if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3
+            select PM_SLP_DISABLE_GPIO if FREERTOS_USE_TICKLESS_IDLE
+            help
+                esp32c3 and esp32s3 will reset at wake-up if GPIO is received a small electrostatic
+                pulse during light sleep, with specific condition
+
+                - GPIO needs to be configured as input-mode only
+                - The pin receives a small electrostatic pulse, and reset occurs when the pulse
+                  voltage is higher than 6 V
+
+                For GPIO set to input mode only, it is not a good practice to leave it open/floating,
+                The hardware design needs to controlled it with determined supply or ground voltage
+                is necessary.
+
+                This option provides a software workaround for this issue. Configure to isolate all
+                GPIO pins in sleep state.
+
         config ESP_SLEEP_PSRAM_LEAKAGE_WORKAROUND
             bool "PSRAM leakage current workaround in light sleep"
             depends on SPIRAM

components/esp_hw_support/sdkconfig.rename

@@ -6,3 +6,4 @@ CONFIG_TWO_UNIVERSAL_MAC_ADDRESS                        CONFIG_ESP32_UNIVERSAL_M
 CONFIG_FOUR_UNIVERSAL_MAC_ADDRESS                       CONFIG_ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR
 
 CONFIG_ESP_SYSTEM_PD_FLASH                              CONFIG_ESP_SLEEP_POWER_DOWN_FLASH
+CONFIG_ESP32C3_LIGHTSLEEP_GPIO_RESET_WORKAROUND         CONFIG_ESP_SLEEP_GPIO_RESET_WORKAROUND

components/esp_system/startup.c

@@ -434,7 +434,7 @@ IRAM_ATTR ESP_SYSTEM_INIT_FN(init_components0, BIT(0))
 {
     esp_timer_init();
 
-#if CONFIG_ESP32C3_LIGHTSLEEP_GPIO_RESET_WORKAROUND && !CONFIG_PM_SLP_DISABLE_GPIO
+#if CONFIG_ESP_SLEEP_GPIO_RESET_WORKAROUND && !CONFIG_PM_SLP_DISABLE_GPIO
     // Configure to isolate (disable the Input/Output/Pullup/Pulldown
     // function of the pin) all GPIO pins in sleep state
     esp_sleep_config_gpio_isolate();