mirror of
https://github.com/espressif/esp-idf.git
synced 2025-08-10 04:43:33 +00:00
soc: moved kconfig options out of the target component.
Moved the following kconfig options out of the target component: * CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system * ESP*_REV_MIN -> esp_hw_support * ESP*_TIME_SYSCALL -> newlib * ESP*_RTC_* -> esp_hw_support Where applicable these target specific konfig names were merged into a single common config, e.g; CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
This commit is contained in:
Marius Vikhammer
@@ -1,131 +0,0 @@
|
||||
menu "ESP32C3-Specific"
|
||||
visible if IDF_TARGET_ESP32C3
|
||||
|
||||
choice ESP32C3_DEFAULT_CPU_FREQ_MHZ
|
||||
prompt "CPU frequency"
|
||||
default ESP32C3_DEFAULT_CPU_FREQ_40 if IDF_ENV_FPGA
|
||||
default ESP32C3_DEFAULT_CPU_FREQ_160 if !IDF_ENV_FPGA
|
||||
help
|
||||
CPU frequency to be set on application startup.
|
||||
|
||||
config ESP32C3_DEFAULT_CPU_FREQ_40
|
||||
bool "40 MHz"
|
||||
depends on IDF_ENV_FPGA
|
||||
config ESP32C3_DEFAULT_CPU_FREQ_80
|
||||
bool "80 MHz"
|
||||
config ESP32C3_DEFAULT_CPU_FREQ_160
|
||||
bool "160 MHz"
|
||||
endchoice
|
||||
|
||||
config ESP32C3_DEFAULT_CPU_FREQ_MHZ
|
||||
int
|
||||
default 40 if ESP32C3_DEFAULT_CPU_FREQ_40
|
||||
default 80 if ESP32C3_DEFAULT_CPU_FREQ_80
|
||||
default 160 if ESP32C3_DEFAULT_CPU_FREQ_160
|
||||
|
||||
choice ESP32C3_REV_MIN
|
||||
prompt "Minimum Supported ESP32-C3 Revision"
|
||||
default ESP32C3_REV_MIN_3
|
||||
help
|
||||
Minimum revision that ESP-IDF would support.
|
||||
|
||||
Only supporting higher chip revisions can reduce binary size.
|
||||
|
||||
config ESP32C3_REV_MIN_0
|
||||
bool "Rev 0"
|
||||
config ESP32C3_REV_MIN_1
|
||||
bool "Rev 1"
|
||||
config ESP32C3_REV_MIN_2
|
||||
bool "Rev 2"
|
||||
config ESP32C3_REV_MIN_3
|
||||
bool "Rev 3"
|
||||
config ESP32C3_REV_MIN_4
|
||||
bool "Rev 4"
|
||||
endchoice
|
||||
|
||||
config ESP32C3_REV_MIN
|
||||
int
|
||||
default 0 if ESP32C3_REV_MIN_0
|
||||
default 1 if ESP32C3_REV_MIN_1
|
||||
default 2 if ESP32C3_REV_MIN_2
|
||||
default 3 if ESP32C3_REV_MIN_3
|
||||
default 4 if ESP32C3_REV_MIN_4
|
||||
|
||||
choice ESP32C3_TIME_SYSCALL
|
||||
prompt "Timers used for gettimeofday function"
|
||||
default ESP32C3_TIME_SYSCALL_USE_RTC_SYSTIMER
|
||||
help
|
||||
This setting defines which hardware timers are used to
|
||||
implement 'gettimeofday' and 'time' functions in C library.
|
||||
|
||||
- If both high-resolution (systimer) and RTC timers are used, timekeeping will
|
||||
continue in deep sleep. Time will be reported at 1 microsecond
|
||||
resolution. This is the default, and the recommended option.
|
||||
- If only high-resolution timer (systimer) is used, gettimeofday will
|
||||
provide time at microsecond resolution.
|
||||
Time will not be preserved when going into deep sleep mode.
|
||||
- If only RTC timer is used, timekeeping will continue in
|
||||
deep sleep, but time will be measured at 6.(6) microsecond
|
||||
resolution. Also the gettimeofday function itself may take
|
||||
longer to run.
|
||||
- If no timers are used, gettimeofday and time functions
|
||||
return -1 and set errno to ENOSYS.
|
||||
- When RTC is used for timekeeping, two RTC_STORE registers are
|
||||
used to keep time in deep sleep mode.
|
||||
|
||||
config ESP32C3_TIME_SYSCALL_USE_RTC_SYSTIMER
|
||||
bool "RTC and high-resolution timer"
|
||||
select ESP_TIME_FUNCS_USE_RTC_TIMER
|
||||
select ESP_TIME_FUNCS_USE_ESP_TIMER
|
||||
config ESP32C3_TIME_SYSCALL_USE_RTC
|
||||
bool "RTC"
|
||||
select ESP_TIME_FUNCS_USE_RTC_TIMER
|
||||
config ESP32C3_TIME_SYSCALL_USE_SYSTIMER
|
||||
bool "High-resolution timer"
|
||||
select ESP_TIME_FUNCS_USE_ESP_TIMER
|
||||
config ESP32C3_TIME_SYSCALL_USE_NONE
|
||||
bool "None"
|
||||
select ESP_TIME_FUNCS_USE_NONE
|
||||
endchoice
|
||||
|
||||
choice ESP32C3_RTC_CLK_SRC
|
||||
prompt "RTC clock source"
|
||||
default ESP32C3_RTC_CLK_SRC_INT_RC
|
||||
help
|
||||
Choose which clock is used as RTC clock source.
|
||||
|
||||
config ESP32C3_RTC_CLK_SRC_INT_RC
|
||||
bool "Internal 150kHz RC oscillator"
|
||||
config ESP32C3_RTC_CLK_SRC_EXT_CRYS
|
||||
bool "External 32kHz crystal"
|
||||
select ESP_SYSTEM_RTC_EXT_XTAL
|
||||
config ESP32C3_RTC_CLK_SRC_EXT_OSC
|
||||
bool "External 32kHz oscillator at 32K_XP pin"
|
||||
select ESP_SYSTEM_RTC_EXT_OSC
|
||||
config ESP32C3_RTC_CLK_SRC_INT_8MD256
|
||||
bool "Internal 8MHz oscillator, divided by 256 (~32kHz)"
|
||||
endchoice
|
||||
|
||||
config ESP32C3_RTC_CLK_CAL_CYCLES
|
||||
int "Number of cycles for RTC_SLOW_CLK calibration"
|
||||
default 3000 if ESP32C3_RTC_CLK_SRC_EXT_CRYS || ESP32C3_RTC_CLK_SRC_EXT_OSC || ESP32C3_RTC_CLK_SRC_INT_8MD256
|
||||
default 1024 if ESP32C3_RTC_CLK_SRC_INT_RC
|
||||
range 0 27000 if ESP32C3_RTC_CLK_SRC_EXT_CRYS || ESP32C3_RTC_CLK_SRC_EXT_OSC || ESP32C3_RTC_CLK_SRC_INT_8MD256
|
||||
range 0 32766 if ESP32C3_RTC_CLK_SRC_INT_RC
|
||||
help
|
||||
When the startup code initializes RTC_SLOW_CLK, it can perform
|
||||
calibration by comparing the RTC_SLOW_CLK frequency with main XTAL
|
||||
frequency. This option sets the number of RTC_SLOW_CLK cycles measured
|
||||
by the calibration routine. Higher numbers increase calibration
|
||||
precision, which may be important for applications which spend a lot of
|
||||
time in deep sleep. Lower numbers reduce startup time.
|
||||
|
||||
When this option is set to 0, clock calibration will not be performed at
|
||||
startup, and approximate clock frequencies will be assumed:
|
||||
|
||||
- 150000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
|
||||
- 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more.
|
||||
In case more value will help improve the definition of the launch of the crystal.
|
||||
If the crystal could not start, it will be switched to internal RC.
|
||||
|
||||
endmenu # ESP32C3-Specific
|
||||
Reference in New Issue
Block a user