Merge branch 'feature/usb_esp32s3_add_host_support' into 'master'

usb/hal/soc: add USB Host support on ESP32-S3

Closes IDF-2713

See merge request espressif/esp-idf!13522

components/esp32s3/ld/esp32s3.peripherals.ld

@@ -37,4 +37,5 @@ PROVIDE ( DMA = 0x6003F000 );
 PROVIDE ( APB_SARADC = 0x60040000 );
 PROVIDE ( LCD_CAM    = 0x60041000 );
 PROVIDE ( USB0     = 0x60080000 );
+PROVIDE ( USBH     = 0x60080000 );
 PROVIDE ( USB_WRAP = 0x60039000 );

components/hal/CMakeLists.txt

@@ -66,7 +66,7 @@ if(NOT BOOTLOADER_BUILD)
                     "esp32s2/touch_sensor_hal.c"
                     "esp32s2/dac_hal.c"
                     "esp32s2/interrupt_descriptor_table.c"
-                    "esp32s2/usbh_hal.c")
+                    "usbh_hal.c")
     endif()
 
     if(${target} STREQUAL "esp32s3")
@@ -81,7 +81,8 @@ if(NOT BOOTLOADER_BUILD)
             "usb_hal.c"
             "esp32s3/brownout_hal.c"
             "esp32s3/interrupt_descriptor_table.c"
-            "esp32s3/touch_sensor_hal.c")
+            "esp32s3/touch_sensor_hal.c"
+            "usbh_hal.c")
     endif()
 
     if(${target} STREQUAL "esp32c3")

components/hal/component.mk

@@ -2,7 +2,7 @@ COMPONENT_SRCDIRS := . esp32
 COMPONENT_ADD_INCLUDEDIRS := esp32/include include
 COMPONENT_ADD_LDFRAGMENTS += linker.lf
 
-COMPONENT_OBJEXCLUDE += ./spi_slave_hd_hal.o ./spi_flash_hal_gpspi.o ./spi_slave_hd_hal.o ./ds_hal.o ./gdma_hal.o ./lcd_hal.o ./systimer_hal.o ./usb_hal.o
+COMPONENT_OBJEXCLUDE += ./spi_slave_hd_hal.o ./spi_flash_hal_gpspi.o ./spi_slave_hd_hal.o ./ds_hal.o ./gdma_hal.o ./lcd_hal.o ./systimer_hal.o ./usb_hal.o ./usbh_hal.o
 
 ifndef CONFIG_ETH_USE_ESP32_EMAC
     COMPONENT_OBJEXCLUDE += esp32/emac_hal.o

components/hal/include/hal/usbh_hal.h

@@ -495,7 +495,7 @@ static inline bool usbh_hal_port_check_if_connected(usbh_hal_context_t *hal)
  * @note This function should only be called after confirming that a device is connected to the host port
  *
  * @param hal Context of the HAL layer
- * @return usb_priv_speed_t Speed of the connected device (FS or LS only on the esp32-s2)
+ * @return usb_priv_speed_t Speed of the connected device (FS or LS only on the esp32-s2 and esp32-s3)
  */
 static inline usb_priv_speed_t usbh_hal_port_get_conn_speed(usbh_hal_context_t *hal)
 {

components/hal/include/hal/usbh_ll.h

@@ -443,13 +443,13 @@ static inline void usbh_ll_hcfg_set_fsls_pclk_sel(usbh_dev_t *hw)
 static inline void usbh_ll_hcfg_set_defaults(usbh_dev_t *hw, usb_priv_speed_t speed)
 {
     hw->hcfg_reg.descdma = 1;   //Enable scatt/gatt
-    hw->hcfg_reg.fslssupp = 1;  //FS/LS supp only
+    hw->hcfg_reg.fslssupp = 1;  //FS/LS support only
     /*
     Indicate to the OTG core what speed the PHY clock is at
     Note: It seems like our PHY has an implicit 8 divider applied when in LS mode,
           so the values of FSLSPclkSel and FrInt have to be adjusted accordingly.
     */
-    hw->hcfg_reg.fslspclksel = (speed == USB_PRIV_SPEED_FULL) ? 1 : 2;  //esp32-s2 only supports FS or LS
+    hw->hcfg_reg.fslspclksel = (speed == USB_PRIV_SPEED_FULL) ? 1 : 2;  //PHY clock on esp32-sx for FS/LS-only
     hw->hcfg_reg.perschedena = 0;   //Disable perio sched
 }
 
@@ -465,7 +465,7 @@ static inline void usbh_ll_hfir_set_defaults(usbh_dev_t *hw, usb_priv_speed_t sp
     Note: It seems like our PHY has an implicit 8 divider applied when in LS mode,
           so the values of FSLSPclkSel and FrInt have to be adjusted accordingly.
     */
-    hfir.frint = (speed == USB_PRIV_SPEED_FULL) ? 48000 : 6000; //esp32-s2 only supports FS or LS
+    hfir.frint = (speed == USB_PRIV_SPEED_FULL) ? 48000 : 6000; //esp32-sx targets only support FS or LS
     hw->hfir_reg.val = hfir.val;
 }
 
@@ -550,7 +550,7 @@ static inline uint32_t usbh_ll_get_frame_list_base_addr(usbh_dev_t *hw)
 static inline usb_priv_speed_t usbh_ll_hprt_get_speed(usbh_dev_t *hw)
 {
     usb_priv_speed_t speed;
-    //esp32-s2 only supports FS or LS
+    //esp32-s2 and esp32-s3 only support FS or LS
     switch (hw->hprt_reg.prtspd) {
         case 1:
             speed = USB_PRIV_SPEED_FULL;

components/hal/usbh_hal.c

@@ -16,6 +16,7 @@
 #include <stdint.h>
 #include <assert.h>
 #include <string.h>
+#include "sdkconfig.h"
 #include "hal/usbh_hal.h"
 #include "hal/usbh_ll.h"
 
@@ -70,7 +71,7 @@
  * - Those bits proxy their interrupt through the USBH_LL_INTR_CHAN_CHHLTD bit
  * - USBH_LL_INTR_CHAN_XCS_XACT_ERR is always unmasked
  * - When USBH_LL_INTR_CHAN_BNAINTR occurs, USBH_LL_INTR_CHAN_CHHLTD will NOT.
- * - USBH_LL_INTR_CHAN_AHBERR doesn't actually ever happen on our system )i.e., ESP32S2 and later):
+ * - USBH_LL_INTR_CHAN_AHBERR doesn't actually ever happen on our system (i.e., ESP32-S2, ESP32-S3):
  *      - If the QTD list's starting address is an invalid address (e.g., NULL), the core will attempt to fetch that
  *        address for a transfer descriptor and probably gets all zeroes. It will interpret the zero as a bad QTD and
  *        return a USBH_LL_INTR_CHAN_BNAINTR instead.
@@ -94,7 +95,11 @@ static void set_defaults(usbh_hal_context_t *hal)
     usbh_ll_internal_phy_conf(hal->wrap_dev);   //Enable and configure internal PHY
     //GAHBCFG register
     usb_ll_en_dma_mode(hal->dev);
-    usb_ll_set_hbstlen(hal->dev, 1);    //Use INCR AHB burst. MUST DO SO IN ESP32-S2 DUE TO ARBITER ERRATA.
+#ifdef CONFIG_IDF_TARGET_ESP32S2
+    usb_ll_set_hbstlen(hal->dev, 1);    //Use INCR AHB burst. See the ESP32-S2 and later chip ERRATA.
+#elif CONFIG_IDF_TARGET_ESP32S3
+    usb_ll_set_hbstlen(hal->dev, 0);    //Do not use USB burst INCR mode for the ESP32-S3, to avoid interference with other peripherals.
+#endif
     //GUSBCFG register
     usb_ll_dis_hnp_cap(hal->dev);       //Disable HNP
     usb_ll_dis_srp_cap(hal->dev);       //Disable SRP

components/usb/CMakeLists.txt

@@ -1,7 +1,7 @@
 idf_build_get_property(target IDF_TARGET)
 
-#USB Host is currently only supported on ESP32-S2
-if(NOT "${target}" STREQUAL "esp32s2")
+#USB Host is currently only supported on ESP32-S2, ESP32S3 chips
+if(NOT "${target}" MATCHES "^esp32s[2-3]")
     return()
 endif()
 

components/usb/test/CMakeLists.txt

@@ -1,7 +1,7 @@
 idf_build_get_property(target IDF_TARGET)
 
-#USB Host is currently only supported on ESP32-S2
-if(NOT "${target}" STREQUAL "esp32s2")
+#USB Host is currently only supported on ESP32-S2, ESP32S3 chips
+if(NOT "${target}" MATCHES "^esp32s[2-3]")
     return()
 endif()