Merge branch 'feature/brownout_bringup_c6' into 'master'

BOD: Bringup for ESP32C6

Closes IDF-5345

See merge request espressif/esp-idf!21888

components/hal/esp32c6/include/hal/brownout_ll.h

@@ -0,0 +1,110 @@
+/*
+ * SPDX-FileCopyrightText: 2023 Espressif Systems (Shanghai) CO LTD
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/*******************************************************************************
+ * NOTICE
+ * The ll is not public api, don't use in application code.
+ * See readme.md in hal/readme.md
+ ******************************************************************************/
+
+#pragma once
+#include <stdbool.h>
+#include "soc/lp_analog_peri_struct.h"
+#include "hal/regi2c_ctrl.h"
+#include "soc/regi2c_brownout.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * @brief power down the flash when a brown out happens.
+ *
+ * @param enable true: power down flash. false: not power down
+ */
+static inline void brownout_ll_enable_flash_power_down(bool enable)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_close_flash_ena = enable;
+}
+
+/**
+ * @brief power down the RF circuits when a brown out happens
+ *
+ * @param enable true: power down. false: not power done.
+ */
+static inline void brownout_ll_enable_rf_power_down(bool enable)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_pd_rf_ena = enable;
+}
+
+/**
+ * @brief Enable this to reset brown out
+ *
+ * @note: If brown out interrupt is used, this should be disabled.
+ *
+ * @param reset_ena true: enable reset. false: disable reset.
+ * @param reset_wait brown out reset wait cycles
+ * @param select 1: chip reset, 0: system reset
+ */
+static inline void brownout_ll_reset_config(bool reset_ena, uint32_t reset_wait, uint8_t select)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_reset_wait = reset_wait;
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_reset_ena = reset_ena;
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_reset_sel = select;
+}
+
+/**
+ * @brief Set brown out threshold
+ *
+ * @param threshold brownout threshold
+ */
+static inline void brownout_ll_set_threshold(uint8_t threshold)
+{
+    REGI2C_WRITE_MASK(I2C_BOD, I2C_BOD_THRESHOLD, threshold);
+}
+
+/**
+ * @brief Set this bit to enable the brown out detection
+ *
+ * @param bod_enable true: enable, false: disable
+ */
+static inline void brownout_ll_bod_enable(bool bod_enable)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_intr_ena = bod_enable;
+}
+
+/**
+ * @brief configure the waiting cycles before sending an interrupt
+ *
+ * @param cycle waiting cycles.
+ */
+static inline void brownout_ll_set_intr_wait_cycles(uint8_t cycle)
+{
+    LP_ANA_PERI.bod_mode0_cntl.bod_mode0_intr_wait = cycle;
+}
+
+/**
+ * @brief Enable brown out interrupt
+ *
+ * @param enable true: enable, false: disable
+ */
+static inline void brownout_ll_intr_enable(bool enable)
+{
+    LP_ANA_PERI.int_ena.bod_mode0 = enable;
+}
+
+/**
+ * @brief Clear interrupt bits.
+ */
+__attribute__((always_inline))
+static inline void brownout_ll_intr_clear(void)
+{
+    LP_ANA_PERI.int_clr.bod_mode0 = 1;
+}
+
+#ifdef __cplusplus
+}
+#endif