This commit renames all registers in xtensa/specreg.h to by adding the
prefix XT_REG_. This is done to avoid naming collisions with similar
variable names. A new register file, viz., xt_specreg.h is created. The
previous names are still available to use but have been deprecated.
Closes https://github.com/espressif/esp-idf/issues/12723
Merges https://github.com/espressif/esp-idf/pull/16040
This change addresses a rare but critical issue observed on certain
ESP32-C3 and ESP32-S3 devices, where secure boot verification
intermittently fails due to improper cleanup of crypto peripherals
during a restart.
Background – Restart Behavior in IDF
------------------------------------
In ESP-IDF, when the device restarts (via `esp_restart()` or due to a
panic/exception), a partial peripheral reset is performed followed by a
CPU reset. However, until now, crypto-related peripherals were not
included in this selective reset sequence.
Problem Scenario
----------------
If a restart occurs while the application is in the middle of a bignum
operation (i.e., using the MPI/Bignum peripheral), the ROM code may
encounter an inconsistent peripheral state during the subsequent boot.
This leads to transient RSA-PSS secure boot verification failures.
Following such a failure, the ROM typically triggers a full-chip reset
via the watchdog timer (WDT). This full reset clears the crypto
peripheral state, allowing secure boot verification to succeed on the
next boot.
Risk with Aggressive Revocation
-------------------------------
If secure boot aggressive revocation is enabled (disabled by default in
IDF), this transient verification failure could mistakenly lead to
revocation of the secure boot digest.
If your product configuration has aggressive revocation enabled,
applying this fix is strongly recommended.
Frequency of Occurrence
-----------------------
The issue is rare and only occurs in corner cases involving
simultaneous use of the MPI peripheral and an immediate CPU reset.
Fix
---
This fix ensures that all crypto peripherals are explicitly reset prior
to any software-triggered restart (including panic scenarios),
guaranteeing a clean peripheral state for the next boot and preventing
incorrect secure boot behavior.
This commit replaces the use of portNUM_PROCESSORS and configNUM_CORES
macros in all of ESP-IDF. These macros are needed to realize an SMP
scenario by fetching the number of active cores FreeRTOS is running on.
Instead, a new Kconfig option, CONFIG_FREERTOS_NUMBER_OF_CORES, has been
added as a proxy for the FreeRTOS config option, configNUMBER_OF_CORES.
This new commit is now used to realize an SMP scenario in various places
in ESP-IDF.
[Sudeep Mohanty: Added new Kconfig option CONFIG_FREERTOS_NUMBER_OF_CORES]
Signed-off-by: Sudeep Mohanty <sudeep.mohanty@espressif.com>
This commit deprecates the "freertos/xtensa_context.h" and "xtensa/xtensa_context.h"
include paths. Users should use "xtensa_context.h" instead.
- Replace legacy include paths
- Removed some unnecessary includes of "xtensa_api.h"
- Add warning to compatibility header
This commit deprecates the "freertos/xtensa_api.h" and "xtensa/xtensa_api.h"
include paths. Users should use "xtensa_api.h" instead.
- Replace legacy include paths
- Removed some unnecessary includes of "xtensa_api.h"
- Replaced some calls with "esp_cpu_..." equivalents
- Add warning to compatibility header
Common spi functionality for sharing the SPI bus between modules is moved from esp_driver_spi to
a more fitting location in esp_hw_support (shared HW resource control).
This also allows us to decouple the spi_flash driver from esp_driver_spi, removing
esp_driver_spi and esp_ringbuf from G1 builds.
Now the soc interrupts definitions are scattered around in the esp-idf
which are out of sync. Put interrupts definitions in soc/periph_defs.h
(!ESP32) or soc/soc.h(ESP32) together in soc/interrupts.h.
If the TimerGroup 0 clock is disabled and then reenabled, the watchdog
registers (Flashboot protection included) will be re-enabled, and some
seconds later, will trigger an unintended reset.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
1. Remove RTC_CLOCK_BBPLL_POWER_ON_WITH_USB Kconfig option
During sleep, BBPLL clock always gets disabled
esp_restart does not disable BBPLL clock, so that first stage bootloader log can be printed
2. Add a new Kconfig option PM_NO_AUTO_LS_ON_USJ_CONNECTED
When this option is selected, IDF will constantly monitor USB CDC port connection status.
As long as it gets connected to a HOST, automatic light-sleep will not happen.
Closes https://github.com/espressif/esp-idf/issues/8507
This commit marks all functions in interrupt_controller_hal.h, cpu_ll.h and cpu_hal.h as deprecated.
Users should use functions from esp_cpu.h instead.
Moved the following kconfig options out of the target component:
* CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system
* ESP*_REV_MIN -> esp_hw_support
* ESP*_TIME_SYSCALL -> newlib
* ESP*_RTC_* -> esp_hw_support
Where applicable these target specific konfig names were merged into
a single common config, e.g;
CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
Moved the following kconfig options out of the target component:
* ESP32_X_BROWNOUT_* -> esp_system
* ESP32_X_DEBUG_OCDAWARE -> esp_system
* APP_NO_BLOBS -> build type (main kconfig)
