This change addresses a rare but critical issue observed on certain
ESP32-C3 and ESP32-S3 devices, where secure boot verification
intermittently fails due to improper cleanup of crypto peripherals
during a restart.
Background – Restart Behavior in IDF
------------------------------------
In ESP-IDF, when the device restarts (via `esp_restart()` or due to a
panic/exception), a partial peripheral reset is performed followed by a
CPU reset. However, until now, crypto-related peripherals were not
included in this selective reset sequence.
Problem Scenario
----------------
If a restart occurs while the application is in the middle of a bignum
operation (i.e., using the MPI/Bignum peripheral), the ROM code may
encounter an inconsistent peripheral state during the subsequent boot.
This leads to transient RSA-PSS secure boot verification failures.
Following such a failure, the ROM typically triggers a full-chip reset
via the watchdog timer (WDT). This full reset clears the crypto
peripheral state, allowing secure boot verification to succeed on the
next boot.
Risk with Aggressive Revocation
-------------------------------
If secure boot aggressive revocation is enabled (disabled by default in
IDF), this transient verification failure could mistakenly lead to
revocation of the secure boot digest.
If your product configuration has aggressive revocation enabled,
applying this fix is strongly recommended.
Frequency of Occurrence
-----------------------
The issue is rare and only occurs in corner cases involving
simultaneous use of the MPI peripheral and an immediate CPU reset.
Fix
---
This fix ensures that all crypto peripherals are explicitly reset prior
to any software-triggered restart (including panic scenarios),
guaranteeing a clean peripheral state for the next boot and preventing
incorrect secure boot behavior.
For targets that only contain a USJ peripheral (and not a DWC OTG), their
'usb_fsls_phy_ll.h' headers only contain a single function
('usb_fsls_phy_ll_int_jtag_enable()') whose feature is already covered by
functions in 'usb_serial_jtag_ll.h'. Thus, this header is redundant.
This commit does the following:
- Remove 'usb_fsls_phy_ll.h' for targets that only contain a USJ peripheral
- Rename 'usb_fsls_phy_[hal|ll].[h|c]' to `usb_wrap_[hal|ll].[h|c]` for targets
that contain a DWC OTG peripheral. This better reflects the underlying peripheral
that the LL header accesses.
fix(panic): fixed cache error being reported as illegal instruction
Closes IDF-6398, IDF-5657, IDF-7015, and IDF-6733
See merge request espressif/esp-idf!27430
On riscv chips accessing cache mapped memory regions over the ibus would
result in an illegal instructions exception triggering faster than the cache
error interrupt/exception.
Added a cache error check in the panic handler, if any cache errors are active
the panic handler will now report a cache error, even if the trigger exception
was a illegal instructions.
- add hardware stack guard based on assist-debug module
- enable hardware stack guard by default
- disable hardware stack guard for freertos ci.release test
- refactor rtos_int_enter/rtos_int_exit to change SP register inside them
- fix panic_reason.h header for RISC-V
- update docs to include information about the new feature
If the TimerGroup 0 clock is disabled and then reenabled, the watchdog
registers (Flashboot protection included) will be re-enabled, and some
seconds later, will trigger an unintended reset.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
usb_serial_jtag: Improve the code for the issue of usb cdc device unable to work during sleep
Closes IDFGH-6887
See merge request espressif/esp-idf!20973
1. Remove RTC_CLOCK_BBPLL_POWER_ON_WITH_USB Kconfig option
During sleep, BBPLL clock always gets disabled
esp_restart does not disable BBPLL clock, so that first stage bootloader log can be printed
2. Add a new Kconfig option PM_NO_AUTO_LS_ON_USJ_CONNECTED
When this option is selected, IDF will constantly monitor USB CDC port connection status.
As long as it gets connected to a HOST, automatic light-sleep will not happen.
Closes https://github.com/espressif/esp-idf/issues/8507
Initialize the pmu sleep machine constant when pmu is initialized, and calculate
the pmu sleep time adjustment value and hardware configuration value according
to the machine constant during system sleep.
Calibrate fast OSC before each sleep and use the calibration value to calculate
PMU hardware wait cycles when use the fast OSC as the work clock.
