mirror of
https://github.com/espressif/esp-idf.git
synced 2025-10-31 13:09:38 +00:00
81bfba06e1
Update ESP32-S2-Saola-1 User Guide according to DGAP-60 Closes DGAP-60 See merge request espressif/esp-idf!9632
149 lines
6.2 KiB
ReStructuredText
149 lines
6.2 KiB
ReStructuredText
================
|
|
ESP32-S2-Saola-1
|
|
================
|
|
|
|
:link_to_translation:`zh_CN:[中文]`
|
|
|
|
This user guide provides information on ESP32-S2-Saola-1, a small-sized `ESP32-S2 <https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf>`_ based development board produced by Espressif.
|
|
|
|
.. figure:: ../../../_static/esp32-s2-saola-1-v1.2-isometric.png
|
|
:align: center
|
|
:alt: ESP32-S2-Saola-1
|
|
:figclass: align-center
|
|
|
|
ESP32-S2-Saola-1
|
|
|
|
The document consists of the following major sections:
|
|
|
|
- `Getting started`_: Provides an overview of the ESP32-S2-Saola-1 and hardware/software setup instructions to get started.
|
|
- `Hardware reference`_: Provides more detailed information about the ESP32-S2-Saola-1's hardware.
|
|
- `Related Documents`_: Gives links to related documentation.
|
|
|
|
Getting Started
|
|
===============
|
|
|
|
This section describes how to get started with ESP32-S2-Saola-1. It begins with a few introductory sections about the ESP32-S2-Saola-1, then Section `Start Application Development`_ provides instructions on how to get the ESP32-S2-Saola-1 ready and flash firmware into it.
|
|
|
|
Overview
|
|
--------
|
|
|
|
ESP32-S2-Saola-1 is a small-sized ESP32-S2 based development board produced by Espressif. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-Saola-1 on a breadboard.
|
|
|
|
To cover a wide range of users' needs, ESP32-S2-Saola-1 supports:
|
|
|
|
- `ESP32-S2-WROVER <https://www.espressif.com/sites/default/files/documentation/esp32-s2-wrover_esp32-s2-wrover-i_datasheet_en.pdf>`_
|
|
- `ESP32-S2-WROVER-I <https://www.espressif.com/sites/default/files/documentation/esp32-s2-wrover_esp32-s2-wrover-i_datasheet_en.pdf>`_
|
|
- `ESP32-S2-WROOM <https://www.espressif.com/sites/default/files/documentation/esp32-s2-wroom_esp32-s2-wroom-i_datasheet_en.pdf>`_
|
|
- `ESP32-S2-WROOM-I <https://www.espressif.com/sites/default/files/documentation/esp32-s2-wroom_esp32-s2-wroom-i_datasheet_en.pdf>`_
|
|
|
|
In this guide, we take ESP32-S2-Saola-1 equipped with ESP32-S2-WROVER as an example.
|
|
|
|
Contents and Packaging
|
|
----------------------
|
|
|
|
Retail orders
|
|
^^^^^^^^^^^^^
|
|
|
|
If you order a few samples, each ESP32-S2-Saola-1 comes in an individual package in either antistatic bag or any packaging depending on your retailer.
|
|
|
|
For retail orders, please go to https://www.espressif.com/en/company/contact/buy-a-sample.
|
|
|
|
|
|
Wholesale Orders
|
|
^^^^^^^^^^^^^^^^
|
|
|
|
If you order in bulk, the boards come in large cardboard boxes.
|
|
|
|
For wholesale orders, please check `Espressif Product Ordering Information <https://www.espressif.com/sites/default/files/documentation/espressif_products_ordering_information_en.pdf>`_ (PDF)
|
|
|
|
Description of Components
|
|
-------------------------
|
|
|
|
.. figure:: ../../../_static/esp32-s2-saola-1-v1.2-annotated-photo.png
|
|
:align: center
|
|
:alt: ESP32-S2-Saola-1 - front/back
|
|
:figclass: align-center
|
|
|
|
ESP32-S2-Saola-1 - front
|
|
|
|
.. list-table::
|
|
:widths: 30 70
|
|
:header-rows: 1
|
|
|
|
* - Key Component
|
|
- Description
|
|
* - ESP32-S2-WROVER
|
|
- ESP32-S2-WROVER is a powerful, generic Wi-Fi MCU module that integrates ESP32-S2. It has a PCB antenna, a 4 MB external SPI flash and an additional 2 MB PSRAM.
|
|
* - I/O Connector
|
|
- All available GPIO pins (except for the SPI bus for flash and PSRAM) are broken out to the pin headers on the board. Users can program ESP32-S2 chip to enable multiple functions such as SPI, I2S, UART, I2C, touch sensors, PWM etc.
|
|
* - USB to UART Bridge
|
|
- Single USB-UART bridge chip provides transfer rates up to 3 Mbps.
|
|
* - Boot Button
|
|
- Download button. Holding down **Boot** and then pressing **Reset** initiates Firmware Download mode for downloading firmware through the serial port.
|
|
* - Reset Button
|
|
- Reset button.
|
|
* - 3.3 V Power On LED
|
|
- Turns on when the USB power is connected to the board.
|
|
* - Micro-USB Port
|
|
- USB interface. Power supply for the board as well as the communication interface between a computer and the ESP32-S2 chip.
|
|
* - RGB LED
|
|
- Addressable RGB LED (WS2812), driven by GPIO18.
|
|
|
|
|
|
Start Application Development
|
|
-----------------------------
|
|
|
|
Before powering up your ESP32-S2-Saola-1, please make sure that it is in good condition with no obvious signs of damage.
|
|
|
|
Required Hardware
|
|
^^^^^^^^^^^^^^^^^
|
|
|
|
- ESP32-S2-Saola-1
|
|
- USB 2.0 cable (Standard-A to Micro-B)
|
|
- Computer running Windows, Linux, or macOS
|
|
|
|
Software Setup
|
|
^^^^^^^^^^^^^^
|
|
|
|
Please proceed to :doc:`../../get-started/index`, where Section :ref:`get-started-step-by-step` will quickly help you set up the development environment and then flash an application example into your ESP32-S2-Saola-1.
|
|
|
|
.. note::
|
|
|
|
ESP32-S2 only supports ESP-IDF master or version v4.2 and higher.
|
|
|
|
Hardware Reference
|
|
==================
|
|
|
|
Block Diagram
|
|
-------------
|
|
|
|
A block diagram below shows the components of ESP32-S2-Saola-1 and their interconnections.
|
|
|
|
.. figure:: ../../../_static/esp32-s2-saola-1-v1.2-block-diags.png
|
|
:align: center
|
|
:scale: 70%
|
|
:alt: ESP32-S2-Saola-1 (click to enlarge)
|
|
:figclass: align-center
|
|
|
|
ESP32-S2-Saola-1 (click to enlarge)
|
|
|
|
Power Supply Options
|
|
^^^^^^^^^^^^^^^^^^^^
|
|
|
|
There are three mutually exclusive ways to provide power to the board:
|
|
|
|
- Micro USB port, default power supply
|
|
- 5V and GND header pins
|
|
- 3V3 and GND header pins
|
|
|
|
Related Documents
|
|
=================
|
|
* `ESP32-S2-Saola-1 Schematics <https://dl.espressif.com/dl/schematics/ESP32-S2-SAOLA-1_V1.1_schematics.pdf>`_ (PDF)
|
|
* `ESP32-S2-Saola-1 Dimensions <https://dl.espressif.com/dl/schematics/ESP32-S2-Saola-1_V1.2_Dimensions.pdf>`_ (PDF)
|
|
* `ESP32-S2 Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf>`_ (PDF)
|
|
* `ESP32-S2-WROVER & ESP32-S2-WROVER-I Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32-s2-wrover_esp32-s2-wrover-i_datasheet_en.pdf>`_ (PDF)
|
|
* `ESP32-S2-WROOM & ESP32-S2-WROOM-I Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32-s2-wroom_esp32-s2-wroom-i_datasheet_en.pdf>`_ (PDF)
|
|
* `Espressif Product Ordering Information <https://www.espressif.com/sites/default/files/documentation/espressif_products_ordering_information_en.pdf>`_ (PDF)
|
|
|
|
For other design documentation for the board, please contact us at sales@espressif.com.
|