Set WiFi SSID and WiFi Password and Maximal retry under Example Configuration Options.
Set Static IP address of your device static IP.
Set Static netmask address of your device static netmask address.
Set Static gateway address of your device static gateway address.
Set Choose DNS server with Set manual value as DNS server or Use gateway address as DNS server to configure your DNS server.
Choose Set manual value as DNS server to configure manual DNS server with Main DNS server address and Backup DNS server address.
Set Enable DNS resolve test to resolve your host which input in Domain name to resolve.

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

Note that the output, in particular the order of the output, may vary depending on the environment.

Console output if station connects to AP successfully:

I (563) static_ip: ESP_WIFI_MODE_STA
I (573) wifi:wifi driver task: 3ffc1bfc, prio:23, stack:6656, core=0
I (573) system_api: Base MAC address is not set
I (573) system_api: read default base MAC address from EFUSE
I (603) wifi:wifi firmware version: 6b2834e
I (603) wifi:wifi certification version: v7.0
I (603) wifi:config NVS flash: enabled
I (603) wifi:config nano formating: disabled
I (613) wifi:Init data frame dynamic rx buffer num: 32
I (613) wifi:Init management frame dynamic rx buffer num: 32
I (623) wifi:Init management short buffer num: 32
I (623) wifi:Init dynamic tx buffer num: 32
I (633) wifi:Init static rx buffer size: 1600
I (633) wifi:Init static rx buffer num: 10
I (643) wifi:Init dynamic rx buffer num: 32
I (643) wifi_init: rx ba win: 6
I (643) wifi_init: tcpip mbox: 32
I (653) wifi_init: udp mbox: 6
I (653) wifi_init: tcp mbox: 6
I (653) wifi_init: tcp tx win: 5744
I (663) wifi_init: tcp rx win: 5744
I (663) wifi_init: tcp mss: 1440
I (673) wifi_init: WiFi IRAM OP enabled
I (673) wifi_init: WiFi RX IRAM OP enabled
I (723) phy_init: phy_version 4660,0162888,Dec 23 2020
W (723) phy_init: failed to load RF calibration data (0xffffffff), falling back to full calibration
I (1093) wifi:mode : sta (4c:11:ae:ea:69:fc)
I (1093) wifi:enable tsf
I (1093) static_ip: wifi_init_sta finished.
I (2313) wifi:new:<11,0>, old:<1,0>, ap:<255,255>, sta:<11,0>, prof:1
I (3053) wifi:state: init -> auth (b0)
I (3083) wifi:state: auth -> assoc (0)
I (3213) wifi:new:<11,2>, old:<11,0>, ap:<255,255>, sta:<11,2>, prof:1
I (3213) wifi:state: assoc -> run (10)
I (3233) wifi:connected with myssid, aid = 2, channel 11, 40D, bssid = 34:29:12:43:c5:40
I (3233) wifi:security: WPA2-PSK, phy: bgn, rssi: -7
I (3243) wifi:pm start, type: 1

I (3253) esp_netif_handlers: sta ip: 192.168.4.2, mask: 255.255.255.0, gw: 192.168.4.1
I (3253) static_ip: static ip:192.168.4.2
I (3253) static_ip: connected to ap SSID:myssid password:mypassword
W (3273) wifi:<ba-add>idx:0 (ifx:0, 34:29:12:43:c5:40), tid:5, ssn:2, winSize:64
I (3303) wifi:AP's beacon interval = 102400 us, DTIM period = 1
I (3303) wifi:new:<11,0>, old:<11,2>, ap:<255,255>, sta:<11,0>, prof:1
I (5203) static_ip: Resolved IPv4 address: 119.9.92.99