mirror of
https://github.com/espressif/esp-idf.git
synced 2025-11-03 22:08:28 +00:00
84aa1c0cc3
tusb: cdc, tasks encapsulation, callbacks api, multiple interfaces examples: added serial interface and usb console ci: reimplemented cmake/make test in python with ignore lists IDF-578
88 lines
2.4 KiB
Markdown
88 lines
2.4 KiB
Markdown
| Supported Targets | ESP32-S2 |
|
|
| ----------------- | -------- |
|
|
|
|
# TinyUSB Sample Descriptor
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example shows how to set up ESP32-S2 chip to get log output via Serial Device connection
|
|
|
|
As a USB stack, a TinyUSB component is used.
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
- Any board with the ESP32-S2 chip with USB connectors or with exposed USB's D+ and D- (DATA+/DATA-) pins.
|
|
|
|
If the board has no USB connector, but has the pins connect pins directly to the host (e.g. with DIY cable from any USB connection cable)
|
|
|
|
```
|
|
ESP32-S2 BOARD USB CONNECTOR (type A)
|
|
--
|
|
| || VCC
|
|
[GPIO 19] --------> | || D-
|
|
[GPIO 20] --------> | || D+
|
|
| || GND
|
|
--
|
|
```
|
|
|
|
You can also use power from the USB connector.
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```bash
|
|
idf.py -p PORT flash monitor
|
|
```
|
|
|
|
(Replace PORT with the name of the serial port to use.)
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Serial Connection
|
|
|
|
After program's start and getting of the message of readiness (`Serial device is ready to connect`) you can connect to the board using any serial port terminal application (e.g. CoolTerm).
|
|
|
|
Note: if you want to send data to the target see how to implement it via `tud_cdc_rx_cb` at the `tusb_serial_device` example.
|
|
|
|
## Example Output
|
|
|
|
After the flashing you should see the output at idf monitor:
|
|
|
|
```
|
|
I (340) example: USB initialization
|
|
I (340) TinyUSB: Driver installation...
|
|
I (340) TinyUSB - Descriptors Control: Setting of a descriptor:
|
|
.bDeviceClass = 239
|
|
.bDeviceSubClass = 2,
|
|
.bDeviceProtocol = 1,
|
|
.bMaxPacketSize0 = 64,
|
|
.idVendor = 0x0000303a,
|
|
.idProduct = 0x00004001,
|
|
.bcdDevice = 0x00000100,
|
|
.iManufacturer = 0x01,
|
|
.iProduct = 0x02,
|
|
.iSerialNumber = 0x03,
|
|
.bNumConfigurations = 0x01
|
|
|
|
I (373) TinyUSB: Driver installed
|
|
I (373) example: USB initialization DONE
|
|
I (383) example: log -> UART
|
|
example: print -> stdout
|
|
example: print -> stderr
|
|
...
|
|
|
|
```
|
|
|
|
Other log will be printed to USB:
|
|
```
|
|
I (5382) example: log -> USB
|
|
example: print -> stdout
|
|
example: print -> stderr
|
|
...
|
|
```
|