mirror of
https://github.com/espressif/esp-idf.git
synced 2025-12-27 05:37:32 +00:00
78 lines
3.5 KiB
Markdown
78 lines
3.5 KiB
Markdown
| Supported Targets | ESP32 | ESP32-P4 |
|
|
| ----------------- | ----- | -------- |
|
|
|
|
# Basic Ethernet Example
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
## Overview
|
|
|
|
This example demonstrates basic usage of internal EMAC and `Ethernet driver` together with `esp_netif`. The workflow of the example is as follows:
|
|
|
|
1. Install Ethernet driver
|
|
2. Attach the driver to `esp_netif`
|
|
3. Send DHCP requests and wait for a DHCP lease
|
|
4. If get IP address successfully, then you will be able to ping the device
|
|
|
|
If you have a new simple Ethernet application to go (for example, connect to IoT cloud via Ethernet), try this as a basic template, then add your own code.
|
|
|
|
>[!TIP]
|
|
> For initialization of a wider range of Ethernet PHY chips, including SPI Ethernet modules and for advanced Ethernet configuration options, please use [Component for Ethernet Initialization](https://components.espressif.com/components/espressif/ethernet_init/).
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
To run this example, it's recommended that you have an official Espressif Ethernet capable development board - either [ESP32-Ethernet-Kit](https://docs.espressif.com/projects/esp-dev-kits/en/latest/esp32/esp32-ethernet-kit/index.html) or [ESP32-P4-Function-EV-Board](https://docs.espressif.com/projects/esp-dev-kits/en/latest/esp32p4/esp32-p4-function-ev-board/index.html). This example should also work for 3rd party ESP32 board as long as it's integrated with a IEEE 802.3 compliant Ethernet PHY chip and with the default RMII dataplane GPIO configuration.
|
|
|
|
> [!NOTE]
|
|
> `Generic 802.3 PHY` basic functionality should always work for PHY compliant with IEEE 802.3. However, some specific features might be limited. A typical example is loopback functionality, where certain PHYs may require setting a specific speed mode to operate correctly. If this is a case, use driver tailored to that specific chip.
|
|
|
|
#### Pin Assignment
|
|
|
|
This example uses the default RMII GPIO configuration as defined by `ETH_ESP32_EMAC_DEFAULT_CONFIG` for the specific ESP32 chip (ESP32, ESP32P4, etc.).
|
|
|
|
### Configure the project
|
|
|
|
```
|
|
idf.py menuconfig
|
|
```
|
|
|
|
See common configurations for Ethernet examples from [upper level](../README.md#common-configurations).
|
|
|
|
### Build, Flash, and Run
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
idf.py -p PORT build flash monitor
|
|
```
|
|
|
|
(Replace PORT with the name of the serial port to use.)
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
```bash
|
|
I (394) eth_example: Ethernet Started
|
|
I (3934) eth_example: Ethernet Link Up
|
|
I (3934) eth_example: Ethernet HW Addr 30:ae:a4:c6:87:5b
|
|
I (5864) esp_netif_handlers: eth ip: 192.168.2.151, mask: 255.255.255.0, gw: 192.168.2.2
|
|
I (5864) eth_example: Ethernet Got IP Address
|
|
I (5864) eth_example: ~~~~~~~~~~~
|
|
I (5864) eth_example: ETHIP:192.168.2.151
|
|
I (5874) eth_example: ETHMASK:255.255.255.0
|
|
I (5874) eth_example: ETHGW:192.168.2.2
|
|
I (5884) eth_example: ~~~~~~~~~~~
|
|
```
|
|
|
|
Now you can ping your ESP32 in the terminal by entering `ping 192.168.2.151` (it depends on the actual IP address you get).
|
|
|
|
## Troubleshooting
|
|
|
|
See common troubleshooting for Ethernet examples from [upper level](../README.md#common-troubleshooting).
|
|
|
|
(For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you as soon as possible.)
|