mirror of
https://github.com/espressif/esp-idf.git
synced 2025-10-30 04:42:19 +00:00
75 lines
3.6 KiB
Markdown
75 lines
3.6 KiB
Markdown
# UART Echo Example
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example demonstrates how to utilize UART interfaces by echoing back to the sender any data received on
|
|
configured UART.
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
The example can be run on any ESP32 or ESP32-S2 based development board connected to a PC with a single USB cable for flashing and
|
|
monitoring. The external interface should have 3.3V outputs. You may use e.g. 3.3V compatible USB-to-Serial dongle.
|
|
|
|
### Setup the Hardware
|
|
|
|
Connect the external serial interface to the ESP32(S2) board as follows.
|
|
|
|
```
|
|
---------------------------------------------------------------------------------------
|
|
| Target chip Interface | #define | Default ESP32(S2) Pin| External UART Pin |
|
|
| ----------------------|------------------|----------------------|--------------------
|
|
| Transmit Data (TxD) | EXAMPLE_UART_TXD | GPIO4 | RxD |
|
|
| Receive Data (RxD) | EXAMPLE_UART_RXD | GPIO5 | TxD |
|
|
| Ground | n/a | GND | GND |
|
|
---------------------------------------------------------------------------------------
|
|
```
|
|
Note: The GPIO22 - GPIO25 can not be used with ESP32-S2 chip because they are reserved for internal use. Please refer to UART documentation for selected target.
|
|
|
|
Optionally, you can set-up and use a serial interface that has RTS and CTS signals in order to verify that the
|
|
hardware control flow works. Connect the extra signals according to the following table, configure both extra pins in
|
|
the example code by replacing existing `UART_PIN_NO_CHANGE` macros with the appropriate pin numbers and configure
|
|
UART1 driver to use the hardware flow control by setting `.flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS` and adding
|
|
`.rx_flow_ctrl_thresh = 122`.
|
|
|
|
```
|
|
--------------------------------------------------------------------------------------
|
|
| Target chip Interface | #define | Default ESP32(S2) Pin| External UART Pin |
|
|
| ----------------------|-----------------|----------------------|--------------------
|
|
| Transmit Data (TxD) | ECHO_TEST_RTS | GPIO18 | CTS |
|
|
| Receive Data (RxD) | ECHO_TEST_CTS | GPIO19 | RTS |
|
|
| Ground | n/a | GND | GND |
|
|
--------------------------------------------------------------------------------------
|
|
```
|
|
|
|
### Configure the project
|
|
|
|
Use the command below to configure project using Kconfig menu as showed in the table above.
|
|
The default Kconfig values can be changed such as: EXAMPLE_TASK_STACK_SIZE, EXAMPLE_UART_BAUD_RATE, EXAMPLE_UART_PORT_NUM (Refer to Kconfig file).
|
|
```
|
|
idf.py menuconfig
|
|
```
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
idf.py -p PORT flash monitor
|
|
```
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
Type some characters in the terminal connected to the external serial interface. As result you should see echo in the
|
|
terminal which is used for flashing and monitoring. You can verify if the echo indeed comes from ESP32(S2) board by
|
|
disconnecting either `TxD` or `RxD` pin: no characters will appear when typing.
|
|
|
|
## Troubleshooting
|
|
|
|
You are not supposed to see the echo in the terminal which is used for flashing and monitoring, but in the other UART configured through Kconfig can be used.
|